| Other Testing Instruments |
 |
| Judder testing machine |
 |
This machine is used to measure and evaluate friction characteristics such as temperature, frictional force, sliding velocity, etc. of steel plates, friction materials, ATF and additives of wet clutches. |
Specifications
Max. pressure force: 5kN
Pressure setup: Arbitrary step
Sliding speed: 1-500R.P.M.
Sliding speed setup: Arbitrary step
Friction force: 50N.m
Temperature: 200°C
Heating system: Direct/indirect
Operation pattern: JASO M349
[Technical standard]
JASO M349-01Automatic transmission fluids-test method for anti-shudder performance |
|
|
| High-pressure environmental friction and wear tester |
 |
This testing machine is used to evaluate the frictional characteristics in a pressure container. It can evaluate the frictional characteristics of refrigerants, oil, friction materials, etc. for compressors and so on. It has a load cell inside the pressure container to enable frictional-force measurement with high accuracy. |
Specifications
Max. pressure force: 8kN
Sliding speed: 8000R.P.M.
Friction force: 5N.m
Pressure vessel: 5Mpa
[Industry use] Compressor/Lubricating oil |
|
|
| Reciprocating friction and wear tester |
 |
This testing machine is used to evaluate surface conditions such as friction faces of materials by measuring the frictional force. |
Specifications
Pressure force: 100g - 5kg
Friction coefficient: 0.01 - 1
Friction faces moving distance: 10.0 - 30.0mm
Sliding speed: 6 - 600mm/min.
[Industry use]Sliding matter/painted side/coating film |
|
|
| Bearing friction and wear tester |
 |
This testing machine evaluates the frictional characteristics of radial bearings. The circuit system adopted for the lubricant enables heating up to 80°C. |
Specifications
Max. pressure force: 15kN
Sliding speed: 10000R.P.M.
Safeguard: Printing prevention
[Industry use] Bearing radial , Lubricant oil, Sliding material |
|
|
| Endurance testing machine for bed |
 |
This device is an endurance tester for ordinary home beds. It can also be used as a compression tester. |
Specifications
Endurance test stroke: 0 - 150mm
Max. capacity: 1.5kN
Repetition speed: 160 time/min.
Point of measurement: Programmable automatic operation measuring point compression
Testing speed: 1 - 500mm/min.
Max. capacity: 2kN
[Industry use] Bed, Mat and urethane |
|
|
| Large testing machine for timber |
 |
This device is used to conduct a three- / four-point bending test on wooden pillars. To facilitate the adjustment between the bearings, it is equipped with rails on the base as well as a trolley to transport the sample. |
Specifications
Max. Capacity: 300kN
Distance between fulcrum (lower): 400 - 8100mm
Height to fulcrum: 400mm
Distance between fulcrum (upper): 200 - 2700mm
[Industry use / Technical standard]
Column/square timber JIS Z 2101 Test procedure for timber JAS |
|
|
| EFM-III |
 |
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision. |
Specifications
Max. pressure force: 5kN
Pressure setup: Arbitrary step
Sliding speed range: 1 - 400mm/sec
Sliding speed setup: Arbitrary step
Friction force: 100/200N
Temperature: Max. 3ch (o.p.)
[Industry use / Technical standard]
Hard/semi-hard fabrication resin
JIS K 7218 Testing Methods for Sliding Wear Resistance of Plastics |
|
|
| Automatic tensile testing machine |
 |
This device evaluates the tensile characteristics of plastics and plastic composite materials. The sample is automatically measured for its size and tested when set in the feed section. Very high-precision elasticity measurement is possible. |
Specifications
Max. capacity: 10kN
Test sample storage: Palette or stockholder
Sample dimension point: Width, thickness and length
[Technical standard]
Hard/semi-hard plastic resin JIS K 7161 Plastics - Determination of Tensile Properties
ISO 5271 |
|
|
| Semi-automatic tensile testing machine |
 |
The controller of this testing machine automatically applies an appropriate load and puts the extensometer between the gauge lines, etc. after the sample is set. It provides measurement with high repeatability. |
Specifications
Max. capacity: 10kN
Crosshead speed: 0.05 - 1000mm/min.
[Industry use]
Factory option
Rubber - Tensile properties
Plastics - Tensile properties
ISO 0527/JIS K 7161 |
|
